TORONTO MICROELECTRONICS, INC. TME2106 Processor Pentium Processor Speed 75/90/100/120/133/150/166MHz Chip Set Intel Video Chip Set None Maximum Onboard 128MB (EDO supported) Memory Maximum Video Memory None Cache 256/512KB BIOS AMI Data Bus Integrated 32-bit PCI/ 16-bit ISA Dimensions Unidentified I/O Options Ethernet port, floppy drive interface, IDE interfaces (2), SCSI connector, parallel port, PS/2 mouse interface, serial ports (2), cache slot, temperature indicator connector, auxiliary connector, PC/104 connectors (2) NPU Options None [Image] CONNECTIONS Purpose Location Purpose Location SCSI interface LED D1 PC/104 C & D J9 connector Network/LAN LED DC1A Ethernet port J10 Network/LAN LED DC1B Parallel port J11 Chassis fan power J1 Temperature JP2 indicator connector PS/2 mouse J2 Auxiliary connector JP3 interface Keyboard connector J3 IDE (44-pin) JP4 interface 1 SCSI wide 2 J4 Floppy drive JP5 interface interface External battery J5 IDE (44-pin) JP6 interface 2 Serial port 1 J6 Reset switch S1 Serial port 2 J7 Cache slot SL1 PC/104 A & B J8 connector Note: The location of D1 is unidentified. The orientation of DC1A & DC1B is unidentified. USER CONFIGURABLE SETTINGS Function Label Position » CMOS memory normal operation JP1 Open CMOS memory clear JP1 Closed » Factory configured - do not SW1/1 Unidentified alter » Factory configured - do not SW1/2 Unidentified alter » Factory configured - do not SW1/3 Unidentified alter Watchdog timer enabled SW2/1 On Watchdog timer disabled SW2/1 Off C800-CFFFF enabled SW2/4 On C800-CFFFF disabled SW2/4 Off D0000-D7FFF enabled SW2/5 On D0000-D7FFF disabled SW2/5 Off D8000-DFFFF enabled SW2/6 On D8000-DFFFF disabled SW2/6 Off PS/2 mouse enabled SW2/7 On PS/2 mouse disabled SW2/7 Off Monitor type select CGA SW2/8 On Monitor type select SW2/8 Off monochrome/VGA AUXCLK to backplane enabled SW3/1 On AUXCLK to backplane disabled SW3/1 Off AUXDATA to backplane enabled SW3/2 On AUXDATA to backplane disabled SW3/2 Off SWRST to backplane enabled SW3/3 On SWRST to backplane disabled SW3/3 Off VABT1 to backplane enabled SW3/4 On VBAT1 to backplane disabled SW3/4 Off KBCLK to backplane enabled SW3/5 On KBCLK to backplane disabled SW3/5 Off KBDATA to backplane enabled SW3/6 On KBDATA to backplane disabled SW3/6 Off SPKR OUTPUT to backplane enabled SW3/7 On SPKR OUTPUT to backplane SW3/7 Off disabled KBINH to backplane enabled SW3/8 On KBINH to backplane disabled SW3/8 Off Jumper information unavailable T1 Unidentified Note: SW2/5 must be off for INT47 to be used. DRAM CONFIGURATION Size Bank 0 Bank 1 8MB (2) 1M x 36 None 16MB (2) 2M x 36 None 16MB (2) 1M x 36 (2) 1M x 36 24MB (2) 1M x 36 (2) 2M x 36 32MB (2) 4M x 36 None 32MB (2) 2M x 36 (2) 2M x 36 40MB (2) 1M x 36 (2) 4M x 36 48MB (2) 2M x 36 (2) 4M x 36 64MB (2) 8M x 36 None 64MB (2) 4M x 36 (2) 4M x 36 72MB (2) 1M x 36 (2) 8M x 36 80MB (2) 2M x 36 (2) 8M x 36 96MB (2) 4M x 36 (2) 8M x 36 128MB (2) 8M x 36 (2) 8M x 36 128MB (2) 16M x 36 None CACHE CONFIGURATION Size SL2 256KB 256KB module installed 512KB 512KB module installed CPU SPEED SELECTION CPU Clock Multiplier JP7 SW2/2 SW2/3 SW1/4 speed speed 75MHz 50MHz 1.5x 1 & 2 On On Off 90MHz 60MHz 1.5x 2 & 3 On Off Off 100MHz 66MHz 1.5x 2 & 3 Off On Off 120MHz 60MHz 2x 2 & 3 On Off On 133MHz 66MHz 2x 2 & 3 Off On On 150MHz 60MHz 2.5x 2 & 3 On Off On 166MHz 66MHz 2.5x 2 & 3 Off On On Note: Pins designated should be in the closed position. If 150MHz or 166MHz CPU is used, install R40 (0 Ohm) & R39 (10K). DIAGNOSTIC LED(S) LED Color Status Condition DC1A/B Green On UTP link is good DC1A/B Green Off LAN controller in AUI mode DC1A/B Red On LAN controller detects a collision in TPI mode DC1A/B Red Off No collision detected by LAN controller