ACQUTEK CORPORATION

PM-I386SX, PM-I486XC

Processor               80386SX/486SLC/486SLC2
Processor Speed         33/40/50MHz
Chip Set                Unidentified
Video Chip Set          None
Maximum Onboard Memory  16MB
Maximum Video Memory    None
Cache                   None
BIOS                    AMI/Award
Dimensions              Unidentified
I/O Options             Floppy drive interface, IDE interface, parallel
                        port, serial ports (2)
NPU Options             80387SX

[Image]

                                CONNECTIONS

  Purpose                   Location   Purpose                   Location

  Serial port 1               CN1      IDE interface               JP5

  Serial port 2               CN2      Floppy drive interface      JP6

  Power LED & keylock         J1       Parallel port               JP7

  Turbo LED                   JP1      Speaker                    JP14

  Turbo switch                JP2      PC bus connector           JP18

  Reset switch                JP3      Power connector            JP19

  IDE interface LED           JP4

                        USER CONFIGURABLE SETTINGS

                Function                      Label          Position

  »   Parallel port unidirectional        JP11/pins 3 &        Open
                                                6

      Parallel port bidirectional         JP11/pins 3 &       Closed
                                                6

  »   Monitor type select color               JP16            Closed

      Monitor type select monochrome          JP16             Open

  »   Factory configured - do not             JP68             Open
      alter

  »   Parity disabled                     JP69/pins 1 &       Closed
                                                2

      Parity enabled                      JP69/pins 1 &        Open
                                                2

              SIMM CONFIGURATION

      Size          Bank 0          Bank 1

     512KB        (2) 256K x 9       None

      1MB         (2) 256K x 9   (2) 256K x 9

      2MB         (2) 1M x 9         None

      4MB         (2) 1M x 9      (2) 1M x 9

      8MB         (2) 4M x 9         None

      16MB        (2) 4M x 9      (2) 4M x 9

                     VDISK CONFIGURATION

  Note: Board will accept up to 4MB of virtual disk memory.

                         VDISK TYPE CONFIGURATION

         Type            JP17/pins 1 &    JP17/pins 2 &     JP17/pins 3 &
                               7                8                9

  »     EPROM/Flash          Open             Open              Open

            SRAM            Closed           Closed            Closed

                     VDISK LOGIC DRIVER CONFIGURATION

         Drive             JP17/pins 4 & 10          JP17/pins 5 & 11

  »          A                  Closed                    Closed

             B                  Closed                     Open

             C                   Open                     Closed

             D                   Open                      Open

                        VDISK ADDRESS CONFIGURATION

                Address                         JP17/pins 6 & 12

  »       EA000H – EFFFFH (24KB)                     Closed

          DA000H – DFFFFH (24KB)                      Open

                            CPU TYPE SELECTION

          Type                    JP15                     JP69

        80386SX             Pins 1 & 2, 4 & 5        Pins 3 & 4, 5 & 6
                                 closed                   closed

         486SLC             Pins 2 & 3, 5 & 6        Pins 3 & 4closed
                                 closed

        486SLC2             Pins 1 & 2, 5 & 6        Pins 5 & 6 closed
                                 closed

                      PARALLEL PORT ADDRESS SELECTION

          Setting              JP11/pins 1 & 4         JP11/pins 2 & 5

  »       LPT1 (378h)                Open                  Closed

          LPT2 (278h)               Closed                  Open

          LPT3 (3BCh)               Closed                 Closed

            Disabled                 Open                   Open

                      SERIAL PORT 1 ADDRESS SELECTION

          Setting              JP13/pins 1 & 7         JP13/pins 2 & 8

  »       COM1 (3F8h)               Closed                  Open

          COM3 (3E8h)                Open                  Closed

            Disabled                 Open                   Open

                      SERIAL PORT 2 ADDRESS SELECTION

          Setting              JP13/pins 3 & 9        JP13/pins 4 & 10

  »       COM2 (2F8h)               Closed                  Open

          COM4 (2E8h)                Open                  Closed

            Disabled                 Open                   Open

                     SERIAL PORT 1 INTERRUPT SELECTION

         IRQ            JP9/pins 1 & 9    JP9/pins 2 &    JP9/pins 3 & 11
                                               10

  »        IRQ3             Open             Closed            Open

           IRQ4            Closed             Open             Open

           IRQ5             Open              Open            Closed

         Disabled           Open              Open             Open

                     SERIAL PORT 2 INTERRUPT SELECTION

         IRQ             JP9/pins 4 &     JP9/pins 5 &    JP9/pins 6 & 15
                             13                14

           IRQ3             Open             Closed            Open

  »        IRQ4            Closed             Open             Open

           IRQ5             Open              Open            Closed

         Disabled           Open              Open             Open

                     PARALLEL PORT INTERRUPT SELECTION

           IRQ                JP9/pins 7 & 15         JP9/pins 8 & 16

  »          None                  Open                     Open

             IRQ7                 Closed                    Open

             IRQ5                  Open                    Closed

                     FLOPPY DRIVE INTERFACE SELECTION

          Setting              JP12/pins 3 & 7         JP12/pins 4 & 8

  »         Enabled                  Open                  Closed

            Disabled                 Open                   Open

                          IDE INTERFACE SELECTION

          Setting              JP12/pins 1 & 5         JP12/pins 2 & 6

  »         Enabled                  Open                  Closed

            Disabled                 Open                   Open

                         WATCH DOG TIMER SELECTION

       Setting          JP10/pins 1 &    JP10/pins 2 &    JP10/pins 3 & 6
                             4                 5

  »     4 seconds          Closed           Closed            Closed

        8 seconds          Closed            Open             Closed

        20 seconds          Open             Open             Closed

         Disabled           N/A               N/A              Open

                            TX ENABLE SELECTION

         Setting              JP13/pins 5 & 11        JP13/pins 6 & 12

  »         Always                  Open                    Open

            RTS = 1                Closed                   Open

            RTS = 2                 Open                   Closed